Hi
The manual says you can set the default margins to YES (and gives the margin data)
What happens if you say NO?
As an enhancement I would like to be able to set a bigger margin all round - even better to be able to set top, bottom, left, right separately.
Cheers
Mark
Margins
Re: Margins
Now there's a good question!!
I shall have to look at my code to see what I was doing here..
Yes, I suppose being able to set custom margins is an idea - not something you could do on the original printer, but of course, margins varied between printer models
I shall have to look at my code to see what I was doing here..
Yes, I suppose being able to set custom margins is an idea - not something you could do on the original printer, but of course, margins varied between printer models
Retro-Printer Specialists
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module
Also Involved in:
Icephorm
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module
Also Involved in:
Icephorm
Re: Margins
Having looked at the source code, at the moment, the default margins setting is only used to set the top and bottom margin.
On Epson printers, this was a DIP switch setting -
A4 Default Margin Top was 8.5mm and Default Margin Bottom was 13.5mm
US Letter Default Margin Top was 9mm and Default Margin Bottom was 9mm
If you set the default to No, then the top and bottom margin are set to zero.
Looking at the code, I realised that there are NO settings for A3 because the Epson manual did not include any settings for this.
So, yes, I need to add default margins for A3 and even A5 page sizes - presumably similar settings?
Being able to specify your own margins is also a good idea.
On Epson printers, this was a DIP switch setting -
A4 Default Margin Top was 8.5mm and Default Margin Bottom was 13.5mm
US Letter Default Margin Top was 9mm and Default Margin Bottom was 9mm
If you set the default to No, then the top and bottom margin are set to zero.
Looking at the code, I realised that there are NO settings for A3 because the Epson manual did not include any settings for this.
So, yes, I need to add default margins for A3 and even A5 page sizes - presumably similar settings?
Being able to specify your own margins is also a good idea.
Retro-Printer Specialists
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module
Also Involved in:
Icephorm
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module
Also Involved in:
Icephorm
Re: Margins
depends on the printer
the left Margin could be adjusted in the fanfold tractor fed machines by shifting the whole paper L-R
and top of form was also effectively manual by adjusting the paper and then that was the top after each FF.
And then of course line spacing some were adjustable.
All nice to haves
the left Margin could be adjusted in the fanfold tractor fed machines by shifting the whole paper L-R
and top of form was also effectively manual by adjusting the paper and then that was the top after each FF.
And then of course line spacing some were adjustable.
All nice to haves
Re: Margins
A3 - 25mm top and left would be fine for me just now
Re: Margins
There is a new setting in v3.15 of the software (currently experimental).
Edit the /root/config/default_margins
You can then set the margins in millimetres in teh following order:
left,top,right,bottom
Use a comma between each value.
Edit the /root/config/default_margins
You can then set the margins in millimetres in teh following order:
left,top,right,bottom
Use a comma between each value.
Retro-Printer Specialists
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module
Also Involved in:
Icephorm
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module
Also Involved in:
Icephorm